LTC3567资料

来源：华拓科技网

元器件交易网www.cecb2b.com

FEATURES

LTC3567High Efﬁ ciency USB Power Manager Plus 1A Buck-Boost Converter with I2C ControlDESCRIPTION

The LTC®3567 is a highly integrated power management and battery charger IC for Li-Ion/Polymer battery applica-tions. It includes a high efﬁ ciency current limited switching PowerPath manager with automatic load prioritization, a battery charger, an ideal diode, and a high efﬁ ciency synchronous buck-boost switching regulator. Designed speciﬁ cally for USB applications, the LTC3567’s switch-ing power manager automatically limits input current to a maximum of either 100mA or 500mA for USB or 1A for adapter-powered applications.The LTC3567’s switching input stage transmits nearly all of the 2.5W available from the USB port to the system load with minimal power wasted as heat. This feature allows the LTC3567 to provide more power to the application and eases thermal budgeting constraints in small spaces.The synchronous buck-boost DC/DC can provide up to 1A output current.The LTC3567 is available in a low proﬁ le 24-pin (4mm × 4mm × 0.75mm) QFN surface mount package.L, LT, LTC and LTM are registered trademarks of Linear Technology Corporation. PowerPath and Bat-Track are a trademarks of Linear Technology Corporation. All other trademarks are the property of their respective owners. Protected by U.S. Patents including 6522118 and 04251.Power Managern High Efﬁ ciency Switching PowerPath™ Controller with Bat-Track™ Adaptive Output Controln Programmable USB or Wall Current Limit (100mA/500mA/1A)n Full Featured Li-Ion/Polymer Battery Chargern “Instant-On” Operation with a Discharged Batteryn 1.5A Maximum Charge Currentn Internal 180mΩ Ideal Diode Plus External Ideal Diode Controller Powers Load in Battery Moden Low No-Load I When Powered from BAT (<30μA)Q1A Buck-Boost DC/DCn High Efﬁ ciency (1A IOUT)n 2.25MHz Constant Frequency Operationn Low No-Load Quiescent Current (~13μA)n Zero Shutdown Currentn I2C Control of All FunctionsAPPLICATIONS

HDD Based MP3 Players, PDA, GPS, PMP Productsn Other USB Based Handheld ProductsnTYPICAL APPLICATION

LTC3567 USB Power Manager with a 3.3V/1A Buck-BoostFROM ACADAPTERFROM USB4.7μF100k0.1μF3.01k2kVBUSCLPROGPROGGATEOPTIONALBATNTCT100kDIGITALCONTROLCHRGCHRGENEN1SCLI2C SERIALINTERFACESDADVCCSWCD1VOUT1324kFB11.5nFVC13567 TA013.3μHSWVOUTVOUT =

BAT + 300mVOTHER DC/DCs

Switching Regulator Efﬁ ciency toSystem Load (POUT/PBUS)1009080

BAT = 4.2VBAT = 3.3V10μF+EFFICIENCY (%)7060504030

Li-Ion1μFLTC3567LDO3V3VIN1SWAB12.2μH3.3V/20mAALWAYSON LDO

1μF3.3V/1AHDD10μF105k201000.01

VBUS = 5VIBAT = 0mA10x MODE0.1IOUT (A)

3567 TA01b

3567f1元器件交易网www.cecb2b.com

LTC3567ABSOLUTE MAXIMUM RATINGS

(Note 1)PIN CONFIGURATION

TOP VIEWCHRGENVBUSVOUTSWCD1EN1BAT18GATE17GND

16CHRG15PROG14SDA13SCL

7SWAB18DVCC9101112VOUT1VIN1GNDVBUS (Transient) t<1ms, Duty Cycle<1% ......–0.3V to 7VVBUS (Static), VIN1, BAT, NTC, CHRG, DVCC, SCL, SDA, EN1, CHRGEN .................................–0.3V to 6VFB1, VC1 .................–0.3V to Lesser of 6V or VIN1 + 0.3VICLPROG ....................................................................3mAICHRG ......................................................................50mAIPROG ........................................................................2mAILDO3V3 ...................................................................30mAISW, IBAT, IVOUT ............................................................2AIVOUT1, ISWAB1, ISWCD1, ............................................2.5AOperating Temperature Range (Note 2)....–40°C to 85°CJunction Temperature (Note 3) .............................125°CStorage Temperature Range ...................–65°C to 125°C242322212019

LDO3V31CLPROG2

NTC3FB14VC15GND6

UF PACKAGE

24-LEAD (4mm × 4mm) PLASTIC QFN

TJMAX = 125°C, θJA = 37°C/WEXPOSED PAD (PIN 25) IS GND, MUST BE SOLDERED TO PCBORDER INFORMATION

LEAD FREE FINISHLTC3567EUF#PBFTAPE AND REELLTC3567EUF#TRPBFPART MARKING3567PACKAGE DESCRIPTION24-Lead (4mm × 4mm) Plastic QFNTEMPERATURE RANGE–40°C to 85°CConsult LTC Marketing for parts speciﬁ ed with wider operating temperature ranges.Consult LTC Marketing for information on non-standard lead based ﬁ nish parts.For more information on lead free part marking, go to: http://www.linear.com/leadfree/ For more information on tape and reel speciﬁ cations, go to: http://www.linear.com/tapeandreel/ The l denotes the speciﬁ cations which apply over the full operating temperature range, otherwise speciﬁ cations are at TA = 25°C. VBUS = 5V, VIN1 = VOUT1 = 3.8V, VBAT = 3.8V, DVCC = 3.3V, RPROG = 1k, RCLPROG = 3.01k, unless otherwise noted.SYMBOLVBUSIBUSLIMPARAMETERInput Supply VoltageTotal Input Current1x Mode, VOUT = BAT5x Mode, VOUT = BAT10x Mode, VOUT = BATSuspend Mode, VOUT = BAT1x Mode, IOUT = 0mA5x Mode, IOUT = 0mA10x Mode, IOUT = 0mASuspend Mode, IOUT = 0mAllllELECTRICAL CHARACTERISTICS

CONDITIONSMIN4.35874368000.31SWTYPMAX5.5UNITSVmAmAmAmAmAmAmAmAmA/mAmA/mAmA/mAmA/mA3567fPowerPath Switching Regulator954608600.38715150.0442241133214011.310050010000.50IBUSQVBUS Quiescent CurrenthCLPROG (Note 4)Ratio of Measured VBUS current to 1x ModeCLPROG Program Current5x Mode10x ModeSuspend Mode2元器件交易网www.cecb2b.com

LTC3567E LECTRICAL CHARACTERISTICS The l denotes the speciﬁ cations which apply over the full operating SYMBOLIOUT (POWERPATH)PARAMETERVOUT Current Available Before Loading BATCONDITIONS1x Mode, BAT = 3.3V5x Mode, BAT = 3.3V10x Mode, BAT = 3.3VSuspend ModeMINTYP13567212510.321.1881003.954.304.00200503.4BAT+0.34.74.35MAXtemperature range, otherwise speciﬁ cations are at TA = 25°C. VBUS = 5V, VIN1 = VOUT1 = 3.8V, VBAT = 3.8V, DVCC = 3.3V, RPROG = 1k, RCLPROG = 3.01k, unless otherwise noted.UNITSmAmAmAmAVmVVVmVmVVVCLPROGVUVLO_VBUSVUVLO_VBUS-VBATVOUTCLPROG Servo Voltage in Current 1x, 5x, 10x ModesLimitSuspend ModeVBUS Undervoltage LockoutVBUS to BAT Differential Undervoltage LockoutVOUT VoltageRising ThresholdFalling ThresholdRising ThresholdFalling Threshold1x, 5x, 10x Modes, 0V < BAT < 4.2V, IOUT = 0mA, Battery Charger OffUSB Suspend Mode, IOUT = 250μAl4.51.84.62.250.180.304.72.7VMHzΩΩAAfOSCRPMOS_POWERPATHRNMOS_POWERPATHIPEAK_POWERPATHBattery ChargerVFLOATICHGIBATSwitching FrequencyPMOS On-ResistanceNMOS On-ResistancePeak Switch Current Limit1x, 5x Modes10x Mode234.1794.16598018524.2004.20010222043.5271.0000.10010010224.2214.2351065223538BAT Regulated Output VoltagelVVmAmAμAμAVVmVmA/mAmAConstant Current Mode Charge CurrentBattery Drain CurrentRPROG = 5kVBUS > VUVLO, Battery Charger Off, IOUT = 0μAVBUS = 0V, IOUT = 0μA (Ideal Diode Mode)VPROGVPROG_TRIKLVC/10hPROGITRKLVTRKLΔVTRKLVRECHRGtTERMtBADBAThC/10VCHRGICHRGPROG Pin Servo VoltagePROG Pin Servo Voltage in Trickle VBAT < VTRIKLChargeC/10 Threshold Voltage at PROGRatio of IBAT to PROG Pin CurrentTrickle Charge CurrentTrickle Charge Threshold VoltageTrickle Charge Hysteresis VoltageRecharge Battery Threshold VoltageSafety Timer TerminationBad Battery Termination TimeEnd of Charge Indication Current RatioCHRG Pin Output Low VoltageCHRG Pin Leakage CurrentThreshold Voltage Relative to VFLOATTimer Starts When BAT = VFLOATBAT < VTRKL(Note 5)ICHRG = 5mAVCHRG = 5V–753.30.420.088BAT < VTRKLBAT Rising2.71002.85135–10040.50.165–12550.630.11210013.0VmVmVHourHourmA/mAmVμA3567f3元器件交易网www.cecb2b.com

LTC3567E LECTRICAL CHARACTERISTICS The l denotes the speciﬁ cations which apply over the full operating SYMBOLRON_CHGPARAMETERBattery Charger Power FET On Resistance (Between VOUT and BAT)Junction Temperature in Constant Temperature ModeCold Temperature Fault Threshold VoltageHot Temperature Fault Threshold VoltageNTC Disable Threshold VoltageNTC Leakage CurrentForward VoltageInternal Diode On-Resistance, DropoutInternal Diode Current LimitRegulated Output VoltageClosed-Loop Output ResistanceDropout Output ResistanceLogic Low Input VoltageLogic High Input VoltageEN1 Pull-Down CurrentCHRGEN Pull-Down CurrentInput Supply VoltageDVCC CurrentDVCC UVLOI2C AddressInput High VoltageInput Low VoltageInput High/Low CurrentSDA Output Low VoltageClock Operating FrequencyBus Free Time Between Stop and Start ConditionHold Time After (Repeated) Start ConditionRepeated Start Condition Setup Time1.30.60.6ISDA = 3mA–10703010.4400SCL/SDA = 0kHz1.60.31.00001001[0]%DVCC%DVCCμAVkHzμsμsμs3567ftemperature range, otherwise speciﬁ cations are at TA = 25°C. VBUS = 5V, VIN1 = VOUT1 = 3.8V, VBAT = 3.8V, DVCC = 3.3V, RPROG = 1k, RCLPROG = 3.01k, unless otherwise noted.CONDITIONSMINTYP0.18MAXUNITSΩTLIMNTCVCOLDVHOTVDISINTCIdeal DiodeVFWDRDROPOUTIMAX_DIODEVLDO3V3RCL_LDO3V3ROL_LDO3V3VILVIHIPD_EN1IPD_CHRGENI2C Port (Note 6)DVCCIDVCCVDVCC_UVLOADDRESSVIH, SDA, SCLVIL, SDA, SCLIIH, IIL SDA, SCLVOLSDAfSCLtBUFtHD_STAtSU_STA110°CRising ThresholdHysteresisFalling ThresholdHysteresisFalling ThresholdHysteresisVNTC = VBUS = 5VVBUS = 0V, IOUT = 10mAIOUT = 10mAVBUS = 0V75.033.40.7–5076.51.534.91.51.75078.036.42.750%VBUS%VBUS%VBUS%VBUS%VBUSmVnAmVmVΩA2150.181.6Always On 3.3V Supply0mA < ILDO3V3 < 25mA3.13.34230.41.21.61.6105.513.5VΩΩVVμAμAVμAVLogic (CHRGEN, EN1)4元器件交易网www.cecb2b.com

LTC3567E LECTRICAL CHARACTERISTICS The l denotes the speciﬁ cations which apply over the full operating SYMBOLtSU_STOtHD_DAT (O)tHD_DAT (I)tSU_DATtLOWtHIGHtftrtSPPARAMETERStop Condition Setup TimeData Hold Time OutputData Hold Time InputData Setup TimeSCL Clock Low PeriodSCL Clock High PeriodClock/Data Fall TimeClock/Data Rise TimeInput Spike Suppression Pulse WidthInput Supply VoltageVOUT UVLO – VOUT FallingVOUT UVLO – VOUT RisingOscillator FrequencyInput CurrentPWM Mode, IOUT1 = 0μABurst Mode® Operation, IOUT1 = 0μA ShutdownFor Burst Mode Operation or Synchronous PWM Operation5.50PWM ModeBurst Mode OperationBurst Mode Operation2.7V ≤ VIN1 ≤ 5.5V, 2.75V ≤ VOUT1 ≤ 5.5V(Note 6)Full Scale (1,1,1,1)Zero Scale (0,0,0,0)VFB1 = 0.8VSwitches A, DSwitches B, CSwitches A, DSwitches B, CPWM ModePWM Modelllllltemperature range, otherwise speciﬁ cations are at TA = 25°C. VBUS = 5V, VIN1 = VOUT1 = 3.8V, VBAT = 3.8V, DVCC = 3.3V, RPROG = 1k, RCLPROG = 3.01k, unless otherwise noted.CONDITIONSMIN0.6001001.30.6CB = Capacitance of One BUS Line (pF)CB = Capacitance of One BUS Line (pF)20+0.1•CB20+0.1•CB30030050900TYPMAXUNITSμsnsnsnsμsμsnsnsnsBuck-Boost RegulatorVIN1VOUTUVLO2.7VIN1 Connected to VOUT Through Low Impedance. Switching Regulator is Disabled in UVLOl5.52.62.82.252201302.655.602.527503350302.92.74002012.75VVVMHzμAμAμAVVAmAmAmA2.5fOSCIVIN11.8VOUT1(LOW)VOUT1(HIGH)ILIMF1IPEAK1(BURST)IZERO1(BURST)IMAX1(BURST)Minimum Regulated Output VoltageMaximum Regulated Output VoltageForward Current Limit (Switch A)Forward Burst Current Limit (Switch A)Reverse Burst Current Limit (Switch D)Maximum Deliverable Output Current in Burst Mode OperationMaximum Servo VoltageMinimum Servo VoltageVFB1 Servo Voltage Step SizeFB1 Input CurrentPMOS RDS(ON)NMOS RDS(ON)PMOS Switch LeakageNMOS Switch LeakageVOUT1 Pull-Down in ShutdownMaximum Buck Duty CycleMaximum Boost Duty CycleSoft-Start Time2200–3050VFBHIGH1VFBLOW1VLSB1IFB1RDS(ON)PRDS(ON)NILEAK(P)ILEAK(N)RVOUT1DBUCK(MAX)DBOOST(MAX)tSS10.7800.405-500.8000.425250.8200.44550VVmVnAΩΩ0.220.17–1–110100750.511μAμAkΩ%%msBurst Mode is a registered trademark of Linear Technology Corporation.3567f5元器件交易网www.cecb2b.com

LTC3567ELECTRICAL CHARACTERISTICS

Note 1: Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. Exposure to any Absolute Maximum Rating condition for extended periods may affect device reliability and lifetime.Note 2: The LTC3567E is guaranteed to meet performance speciﬁ cations from 0°C to 85°C. Speciﬁ cations over the –40°C to 85°C operating temperature range are assured by design, characterization and correlation with statistical process controls.Note 3: The LTC3567 includes overtemperature protection that is intended to protect the device during momentary overload conditions. Junction temperatures will exceed 125°C when overtemperature protection is active. Continuous operation above the speciﬁ ed maximum operating junction temperature may impair device reliability.Note 4: Total Input current is the sum of quiescent current, IVBUSQ, and measured current given by: VCLPROG/RCLPROG • (hCLPROG + 1)Note 5: hC/10 is expressed as a fraction of measured full charge current with indicated PROG resistor.Note 6: Guaranteed by design.TYPICAL PERFORMANCE CHARACTERISTICS

Ideal Diode V-I Characteristics1.0

INTERNAL IDEAL DIODEWITH SUPPLEMENTALEXTERNAL VISHAYSi2333 PMOSRESISTANCE (Ω)0.25

TA = 25°C unless otherwise noted.Output Voltage vs Output Current(Battery Charger Disabled)4.50

BAT = 4VVBUS = 5V5x MODEIdeal Diode Resistancevs Battery Voltage0.8CURRENT (A)0.20

OUTPUT VOLTAGE (V)INTERNAL IDEALDIODE4.25

0.6

INTERNAL IDEALDIODE ONLY0.4

0.154.00

BAT = 3.4V3.75

0.10

INTERNAL IDEAL DIODEWITH SUPPLEMENTALEXTERNAL VISHAYSi2333 PMOS0.2

VBUS = 0VVBUS = 5V0

0.04

0.120.160.08

FORWARD VOLTAGE (V)

0.20

3567 G01

0.053.50

02.7

3.0

3.63.93.3

BATTERY VOLTAGE (V)

4.2

3567 G02

3.25

0200

600800400

OUTPUT CURRENT (mA)

1000

3567 G03

USB Limited Battery Charge Current vs Battery Voltage700600CHARGE CURRENT (mA)CHARGE CURRENT (mA)500400300200100

5x USB SETTING,BATTERY CHARGER SET FOR 1A3.0

3.3

3.6

3.9

4.2

3567 G04

USB Limited Battery Charge Current vs Battery Voltage1501251007550250

1x USB SETTING,BATTERY CHARGER SET FOR 1A2.7

3.0

3.33.63.9BATTERY VOLTAGE (V)

4.2

3567 G05

Battery Drain Current vs Battery Voltage25

IVOUT = 0μAVBUS = 0VVBUS = 5VRPROG = 1kRCLPROG = 2.94kBATTERY CURRENT (μA)VBUS = 5VRPROG = 1kRCLPROG = 2.94k20

VBUS = 5V(SUSPEND MODE)5

02.7

3.0

BATTERY VOLTAGE (V)

3.63.93.3

BATTERY VOLTAGE (V)

4.2

3567 G06

3567f6元器件交易网www.cecb2b.com

LTC3567TYPICAL PERFORMANCE CHARACTERISTICS

PowerPath Switching Regulator Efﬁ ciency vs Output Current10090EFFICIENCY (%)80706050400.01

602.7

BAT = 3.8V1x MODE100

5x, 10x MODE90EFFICIENCY (%)TA = 25°C unless otherwise noted.VBUS Current vs VBUS Voltage (Suspend)50

BAT = 3.8VIVOUT = 0mABattery Charging Efﬁ ciency vs Battery Voltage with No External Load (PBAT/PBUS)RCLPROG = 3.01kRPROG = 1kIVOUT = 0mA5x CHARGINGEFFICIENCY1x CHARGINGEFFICIENCY80

QUIESCENT CURRENT (μA)4.2

0.1

OUTPUT CURRENT (A)

3567 G07

3.0

3.63.93.3

BATTERY VOLTAGE (V)

BUS VOLTAGE (V)

3567 G09

3567 G08

Output Voltage vs Load Current in Suspend5.0

0.5

VBUS Current vs Load Current in SuspendVBUS = 5VBAT = 3.3VRCLPROG = 2.94kOUTPUT VOLTAGE (V)3.4

3.3V LDO Output Voltage vs Load Current, VBUS = 0VBAT = 3.9V, 4.2VBAT = 3.4VBAT = 3.5VBAT = 3.6V4.5OUTPUT VOLTAGE (V)VBUS CURRENT (mA)0.4

3.2

4.00.3

3.0

3.50.2

3.0

2.5

VBUS = 5VBAT = 3.3VRCLPROG = 2.94k0

0.1

0.30.40.2

LOAD CURRENT (mA)

0.5

3567 G10

0.1

2.8

00.1

0.30.40.2

LOAD CURRENT (mA)

0.5

3567 G11

2.6

BAT = 3VBAT = 3.1VBAT = 3.2VBAT = 3.3V0

152010

LOAD CURRENT (mA)

3567 G12

Battery Charge Current vs Temperature600500CHARGE CURRENT (mA)400

THERMAL REGULATION3002001000

–40–20RPROG = 2k10x MODE0

20406080TEMPERATURE (°C)

100120

3567 G13

Battery Charger Float Voltage vs Temperature4.21

3.68

Low-Battery (Instant-On) Output Voltage vs TemperatureBAT = 2.7VIVOUT = 100mA5x MODEOUTPUT VOLTAGE (V)4.20FLOAT VOLTAGE (V)3.66

4.193.

4.183.62

4.17

–40

–15

3510

TEMPERATURE (°C)

6085

3567 G14

3.60

–40

–15

3510

TEMPERATURE (°C)

6085

3567 G15

3567f7元器件交易网www.cecb2b.com

LTC3567TYPICAL PERFORMANCE CHARACTERISTICS

Oscillator Frequency vs Temperature2.6

TA = 25°C unless otherwise noted.VBUS Quiescent Current in Suspend vs Temperature70

IVOUT = 0μAVBUS Quiescent Current vs TemperatureVBUS = 5VIVOUT = 0μAQUIESCENT CURRENT (μA)60

3567 G17

QUIESCENT CURRENT (mA)2.4FREQUENCY (MHz)VBUS = 5V2.2

BAT = 3VVBUS = 0VBAT = 2.7VVBUS = 0V1.8–40

–15

3510

TEMPERATURE (°C)

BAT = 3.6VVBUS = 0V12

5x MODE60

1x MODE6

2.040

6085

3567 G16

3–40

–15

3510

TEMPERATURE (°C)

30–40

–15

3510

TEMPERATURE (°C)

6085

3567 G18

CHRG Pin Current vs Voltage (Pull-Down State)100

VBUS = 5VBAT = 3.8VILDO3V35mA/DIV

0mA

VLDO3V320mV/DIVAC COUPLED

3.3V LDO Step Response (5mA to 15mA)50

Battery Drain Current vs TemperatureBAT = 3.8VVBUS = 0VBUCK REGULATORS OFFCHRG PIN CURRENT (mA)80

40BATTERY CURRENT (μA)VBAT = 3.8V

20μs/DIV

3567 G20

342

CHRG PIN VOLTAGE (V)

3567 G19

0–40

–15

3510

TEMPERATURE (°C)

6085

3567 G21

RDS(ON) for Buck-Boost Regulator Power Switches vs Temperature0.30

PMOS VIN1 = 3VPMOS VIN1 = 3.6V0.25

PMOS VIN1 = 4.5VPMOS RDS(ON) (Ω)0.200.150.100.05

–55–35–15

NMOS VIN1 = 3VNMOS VIN1 = 3.6VNMOS VIN1 = 4.5V0.400.35

NMOS RDS(ON) (Ω)0.300.250.200.15

0.10

525456585105125TEMPERATURE (°C)

3567 G22

Buck-Boost Regulator Current Limit vs Temperature26002550

VIN1 = 3.6V2500ILIMF (mA)245024002350

2300

–55–35–15

VIN1 = 4.5VIQ (μA)13.012.512.011.5

VIN1 = 3V14.013.5

Buck-Boost Regulator Burst Mode Operation Quiescent CurrentVOUT1 = 3.3VVIN1 = 4.5VVIN1 = 3VVIN1 = 3.6V525456585105125TEMPERATURE (°C)

3567 G23

11.0

–55–35–15

525456585105125TEMPERATURE (°C)

3567 G24

3567f8元器件交易网www.cecb2b.com

LTC3567TYPICAL PERFORMANCE CHARACTERISTICS

Buck-Boost Regulator PWM Mode Efﬁ ciency1009080EFFICIENCY (%)7060504030201000.1

VOUT1 = 3.3VTYPE 3 COMPENSATION10ILOAD (mA)

100

1000

3567 G25

TA = 25°C unless otherwise noted.Buck-Boost Regulator PWM Efﬁ ciency vs VIN110090

100

Buck-Boost Regulator vs ILOADBURST MODE OPERATION90CURVES80

EFFICIENCY (%)VIN1 = 3VVIN1 = 3.6VVIN1 = 4.5V6050403020

10VOUT1 = 3.3VTYPE 3 COMPENSATION0

3.13.92.73.5

VIN1 (V)

ILOAD = 50mAILOAD = 200mAILOAD = 1000mAEFFICIENCY (%)BURST MODEOPERATIONCURVESVIN1 = 3VVIN1 = 3.6VVIN1 = 4.5VPWM MODECURVES8070

70605040302010

VIN1 = 3VVIN1 = 3.6VVIN1 = 4.5VPWM MODECURVESVIN1 = 3VVIN1 = 3.6VVIN1 = 4.5V4.34.7

3567 G26

00.1

VOUT1 = 5VTYPE 3 COMPENSATION1

10ILOAD (mA)

100

1000

3567 G27

Buck-Boost Regulator Load Regulation3.3333.3223.311VOUT1 (V)3.3003.23.2783.267

VOUT1 = 3.3VTYPE 3 COMPENSATION1

ILOAD (mA)

3567 G28

Reduction in Current Deliverability at Low VIN1300250200150100500

CH2 ILOADDC 200mA/DIV

VOUT1 = 3.3VTYPE 3 COMPENSATION2.7

3.1

3.5

3.9VIN1 (V)

4.3

4.7

3567 G29

Buck-Boost Regulator Load Step, 0mA to 300mAREDUCTION BELOW 1A (mA)VIN1 = 3VVIN1 = 3.6VVIN1 = 4.5VSTEADY STATE ILOADSTART-UP WITH ARESISTIVE LOADSTART-UP WITH ACURRENT SOURCE LOADCH1 VOUT1AC 100mV/DIV

1001A

VIN1 = 4.2VVOUT1 = 3.3VL = 2.2μHCOUT = 47μF

100μs/DIV

3567 G30

PIN FUNCTIONS

LDO3V3 (Pin 1): 3.3V LDO Output Pin. This pin provides a regulated always-on, 3.3V supply voltage. LDO3V3 gets its power from VOUT. It may be used for light loads such as a watchdog microprocessor or real time clock. A 1μF capacitor is required from LDO3V3 to ground. If the LDO3V3 output is not used it should be disabled by connecting it to VOUT.CLPROG (Pin 2): USB Current Limit Program and Moni-tor Pin. A resistor from CLPROG to ground determines the upper limit of the current drawn from the VBUS pin. A fraction of the VBUS current is sent to the CLPROG pin when the synchronous switch of the PowerPath switching regulator is on. The switching regulator delivers power until the CLPROG pin reaches 1.188V. Several VBUS cur-rent limit settings are available via user input which will typically correspond to the 500mA and the 100mA USB speciﬁ cations. A multilayer ceramic averaging capacitor or R-C network is required at CLPROG for ﬁ ltering.NTC (Pin 3): Input to the Thermistor Monitoring Circuits. The NTC pin connects to a battery’s thermistor to deter-mine if the battery is too hot or too cold to charge. If the battery’s temperature is out of range, charging is paused 3567f9元器件交易网www.cecb2b.com

LTC3567PIN FUNCTIONS

until it re-enters the valid range. A low drift bias resistor is required from VBUS to NTC and a thermistor is required from NTC to ground. If the NTC function is not desired, the NTC pin should be grounded.FB1 (Pin 4): Feedback Input for the (Buck-Boost) Switching Regulator. When the regulator’s control loop is complete, this pin servos to 1 of 16 possible set-points based on the commanded value from the I2C serial port. See Table 4. er and Voltage VC1 (Pin 5): Output of the Error AmpliﬁCompensation Node for the (Buck-Boost) Switching Regulator. External Type I or Type III compensation (to FB1) connects to this pin. See Applications Section for selecting buck-boost loop compensation components.GND (Pin 6, 12): Power GND Pins for the buck-boost.SWAB1 (Pin 7): Switch Node for the (Buck-Boost) Switch-ing Regulator. Connected to internal power switches A and B. External inductor connects between this node and SWCD1.DVCC (Pin 8): Logic Supply for the I2C Serial Port.VIN1 (Pin 9): Power Input for the (Buck-Boost) Switching Regulator. This pin will generally be connected to VOUT (Pin 20). A 1μF (min) MLCC capacitor is recommended on this pin.VOUT1 (Pin 10): Regulated Output Voltage for the (Buck-Boost) Switching Regulator.SWCD1 (Pin 11): Switch Node for the (Buck-Boost) Switching Regulator. Connected to internal power switches C and D. External inductor connects between this node and SWAB1.SCL (Pin 13): Clock Input Pin for the I2C Serial Port. The I2C logic levels are scaled with respect to DVCC.SDA (Pin 14): Data Input Pin for the I2C Serial Port. The I2C logic levels are scaled with respect to DVCC.PROG (Pin 15): Charge Current Program and Charge Current Monitor Pin. Connecting a resistor from PROG to ground programs the charge current. If sufﬁ cient in-put power is available in constant-current mode, this pin servos to 1V. The voltage on this pin always represents the actual charge current.CHRG (Pin 16): Open-Drain Charge Status Output. The CHRG pin indicates the status of the battery charger. Four possible states are represented by CHRG: charging, not charging, unresponsive battery and battery temperature out of range. CHRG is modulated at 35kHz and switches between a low and high duty cycle for easy recognition by either humans or microprocessors. See Table 1. CHRG requires a pull-up resistor and/or LED to provide indica-tion.GND (Pin 17): GND pin for USB Power Manager.GATE (Pin 18): Analog Output. This pin controls the gate of an optional external P-channel MOSFET transistor used to supplement the ideal diode between VOUT and BAT. The external ideal diode operates in parallel with the internal ideal diode. The source of the P-channel MOSFET should be connected to VOUT and the drain should be connected to BAT. If the external ideal diode FET is not used, GATE should be left ﬂ oating.BAT (Pin 19): Single Cell Li-Ion Battery Pin. Depending on available VBUS power, a Li-Ion battery on BAT will ei-ther deliver power to VOUT through the ideal diode or be charged from VOUT via the battery charger.VOUT (Pin 20): Output Voltage of the Switching Power-Path Controller and Input Voltage of the Battery Charger. The majority of the portable product should be powered from VOUT. The LTC3567 will partition the available power between the external load on VOUT and the internal battery charger. Priority is given to the external load and any extra power is used to charge the battery. An ideal diode from BAT to VOUT ensures that VOUT is powered even if the load exceeds the allotted power from VBUS or if the VBUS power source is removed. VOUT should be bypassed with a low impedance ceramic capacitor.VBUS (Pin 21): Primary Input Power Pin. This pin delivers power to VOUT via the SW pin by drawing controlled current from a DC source such as a USB port or wall adapter.SW (Pin 22): Power Transmission Pin for the USB Pow-erPath. The SW pin delivers power from VBUS to VOUT via the step-down switching regulator. A 3.3μH inductor should be connected from SW to VOUT.3567f10元器件交易网www.cecb2b.com

LTC3567PIN FUNCTIONS

CHRGEN (Pin 23): Logic Input. This logic input pin in-dependently enables the battery charger. Active low. Has a 1.6μA internal pull-down current source. This pin is logically ORed with its corresponding bit in the I2C serial port.EN1 (Pin 24): Logic Input. This logic input pin indepen-dently enables the buck-boost switching regulator. Active high. Has a 1.6μA internal pull-down current source. This pin is logically ORed with its corresponding bit in the I2C serial port.Exposed Pad (Pin 25): Ground. Buck-Boost logic and USB power manager ground connections. The Exposed Pad should be connected to a continuous ground plane on the printed circuit board directly under the LTC3567.BLOCK DIAGRAM

21VBUS2.25MHz PowerPathBUCK REGULATOR3.3V LDOSWLDO3V3221SUSPEND LDO500μA/2.5mA2316VOUT20NTCCHRG+1.2VCHARGESTATUS3.6V+–0.3VCHRGENVIN1ENABLEMODEILIMDECODELOGICCHRGENEN1DVCCSDASCLGND6, 12, 17, 25I2C PORTFB1VC1454D/AVOUT11A, 2.25MHzBUCK-BOOSTREGULATOR109232481413+–++BATTERYTEMPERATUREMONITOR–CLPROG–+IDEALCC/CVCHARGERGATE18–15mVBATPROG1915SWAB17SWCD1113567 BD3567f11元器件交易网www.cecb2b.com

LTC3567TIMING DIAGRAM

DATA BYTE A

ADDRESS

STARTSDASCL

ACK9

WR0

STOP

DATA BYTE B

SDA

tSU, DATtLOWSCLtHD, STASTARTCONDITION

trtHIGHtfREPEATED STARTCONDITION

tSPSTOPCONDITION

STARTCONDITION

tHD, DATtSU, STAtHD, STAtBUFtSU, STO3567 TDOPERATION

IntroductionThe LTC3567 is a highly integrated power management IC which includes a high efﬁ ciency switch mode PowerPath controller, a battery charger, an ideal diode, an always-on LDO and a 1A buck-boost switching regulator. The entire chip is controllable via an I2C serial port.Designed speciﬁ cally for USB applications, the PowerPath controller incorporates a precision average input current step-down switching regulator to make maximum use of the allowable USB power. Because power is conserved, the LTC3567 allows the load current on VOUT to exceed the current drawn by the USB port without exceeding the USB load speciﬁ cations.The PowerPath switching regulator and battery charger communicate to ensure that the input current never vio-lates the USB speciﬁ cations.The ideal diode from BAT to VOUT guarantees that ample -power is always available to VOUT even if there is insufﬁcient or absent power at VBUS.An “always-on” LDO provides a regulated 3.3V from avail-able power at VOUT. Drawing very little quiescent current, this LDO will be on at all times and can be used to supply up to 25mA.The LTC3567 also has a general purpose buck-boost switching regulator, which can be independently enabled via direct digital control or the I2C serial port. Along with constant frequency PWM mode, the buck-boost regulator has a low power burst-only mode setting for signiﬁ cantly reduced quiescent current under light load conditions.High Efﬁ ciency Switching PowerPath ControllerWhenever VBUS is available and the PowerPath switching regulator is enabled, power is delivered from VBUS to VOUT via SW. VOUT drives both the external load (including the buck-boost regulator) and the battery charger.If the combined load does not exceed the PowerPath switching regulator’s programmed input current limit, VOUT will track 0.3V above the battery (Bat-Track). By keeping the voltage across the battery charger low, efﬁ ciency is optimized because power lost to the linear battery char-ger is minimized. Power available to the external load is therefore optimized.If the combined load at VOUT is large enough to cause the switching power supply to reach the programmed input current limit, the battery charger will reduce its charge current by the amount necessary to enable the external load to be satisﬁ ed. Even if the battery charge current is 3567f12元器件交易网www.cecb2b.com

LTC3567OPERATION

set to exceed the allowable USB current, the USB speciﬁ ca-tion will not be violated. The switching regulator will limit the average input current so that the USB speciﬁ cation is never violated. Furthermore, load current at VOUT will always be prioritized and only remaining available power will be used to charge the battery.If the voltage at BAT is below 3.3V, or the battery is not present and the load requirement does not cause the switch-ing regulator to exceed the USB speciﬁ cation, VOUT will regulate at 3.6V, thereby providing “Instant-On” operation. If the load exceeds the available power, VOUT will drop to a voltage between 3.6V and the battery voltage. If there is no battery present when the load exceeds the available USB power, VOUT can drop toward ground. The power delivered from VBUS to VOUT is controlled by a 2.25MHz constant-frequency step-down switching regulator. To meet the USB maximum load speciﬁ cation, the switching regulator includes a control loop which ensures that the average input current is below the level programmed at CLPROG.The current at CLPROG is a fraction (hCLPROG–1) of the VBUS current. When a programming resistor and an averaging capacitor are connected from CLPROG to GND, the voltage on CLPROG represents the average input current of the switching regulator. When the input current approaches the programmed limit, CLPROG reaches VCLPROG, 1.188V and power out is held constant. The input current is pro-grammed by the B1 and B0 bits of the I2C serial port. It can be conﬁ gured to limit average input current to one of several possible settings as well as be deactivated (USB suspend). The input current limit will be set by the VCLPROG servo voltage and the resistor on CLPROG according to the following expression: V

IVBUS=IBUSQ+CLPROG•(hCLPROG+1)

RCLPROG

Figure 1 shows the range of possible voltages at VOUT as a function of battery voltage.4.54.23.9VOUT (V)3.63.33.02.72.42.4

NO LOAD300mV2.73.0

3.63.3

BAT (V)

3.94.2

3567 F01

Figure 1. VOUT vs BATIdeal Diode from BAT to VOUTThe LTC3567 has an internal ideal diode as well as a con-troller for an optional external ideal diode. The ideal diode controller is always on and will respond quickly whenever VOUT drops below BAT.2200200018001600CURRENT (mA)14001200100080060040020000

ONSEMICONDUCTORMBRM120LT3VISHAY Si2333OPTIONAL EXTERNALIDEAL DIODELTC3567IDEAL DIODE60120180240300360420480FORWARD VOLTAGE (mV) (BAT – VOUT)

3567 F02

Figure 2. Ideal Diode OperationIf the load current increases beyond the power allowed from the switching regulator, additional power will be pulled from the battery via the internal ideal diode. Furthermore, if power to VBUS (USB or wall power) is removed, then all of the application power will be provided by the battery via the ideal diode. The transition from input power to battery power at VOUT will be quick enough to allow only the 10μF capacitor to keep VOUT from drooping. The ideal diode consists of a precision ampliﬁ er that enables a large on-3567f13元器件交易网www.cecb2b.com

LTC3567OPERATION

chip P-channel MOSFET transistor whenever the voltage at VOUT is approximately 15mV (VFWD) below the voltage at BAT. The resistance of the internal ideal diode is approxi-mately 180mΩ. If this is sufﬁ cient for the application, then no external components are necessary. However, if more conductance is needed, an external P-channel MOSFET transistor can be added from BAT to VOUT.When an external P-channel MOSFET transistor is present, the GATE pin of the LTC3567 drives its gate for automatic ideal diode control. The source of the external P-chan-nel MOSFET should be connected to VOUT and the drain should be connected to BAT. Capable of driving a 1nF load, the GATE pin can control an external P-channel MOSFET transistor having an on-resistance of 40mΩ or lower.Suspend LDOIf the LTC3567 is conﬁ gured for USB suspend mode, the switching regulator is disabled and the suspend LDO provides power to the VOUT pin (presuming there is power available to VBUS). This LDO will prevent the battery from running down when the portable product has access to a suspended USB port. Regulating at 4.6V, this LDO only becomes active when the switching converter is disabled (suspended). To remain compliant with the USB speciﬁ ca-tion, the input to the LDO is current limited so that it will not exceed the 500μA low power suspend speciﬁ cation. If the load on VOUT exceeds the suspend current limit, the additional current will come from the battery via the ideal diode.3.3V Always-On SupplyThe LTC3567 includes a low quiescent current low drop-out regulator that is always powered. This LDO can be used to provide power to a system pushbutton controller, standby microcontroller or real time clock. Designed to deliver up to 25mA, the always-on LDO requires at least a 1μF low impedance ceramic bypass capacitor for compensation. The LDO is powered from VOUT, and therefore will enter dropout at loads less than 25mA as VOUT falls near 3.3V. If the LDO3V3 output is not used, it should be disabled by connecting it to VOUT.VBUS Undervoltage Lockout (UVLO)An internal undervoltage lockout circuit monitors VBUS and keeps the PowerPath switching regulator off until VBUS rises above 4.30V and is at least 200mV above the battery voltage. Hysteresis on the UVLO turns off the regulator if VBUS drops below 4.00V or to within 50mV of BAT. When this happens, system power at VOUT will be drawn from the battery via the ideal diode.TO USBOR WALLADAPTER21VBUSSW22ISWITCH/N3.5V TO(BAT + 0.3V)TO SYSTEMLOADPWM ANDGATE DRIVEIDEALDIODEVOUT20CONSTANT CURRENTCONSTANT VOLTAGEBATTERY CHARGER15mVCLPROG1.206V–++–GATE18OPTIONALEXTERNALIDEAL DIODEPMOS2AVERAGE INPUTCURRENT LIMITCONTROLLERAVERAGE OUTPUTVOLTAGE LIMITCONTROLLER3567 F03Figure 3. PowerPath Block Diagram3567f14++––+0.3V3.6V+–BAT19+SINGLE CELLLi-Ion元器件交易网www.cecb2b.com

LTC3567OPERATION

Battery ChargerThe LTC3567 includes a constant-current/constant-volt-age battery charger with automatic recharge, automatic termination by safety timer, low voltage trickle charging, bad cell detection and thermistor sensor input for out-of-temperature charge pausing.Battery PreconditioningWhen a battery charge cycle begins, the battery charger ﬁ rst determines if the battery is deeply discharged. If the battery voltage is below VTRKL, typically 2.85V, an automatic trickle charge feature sets the battery charge current to 10% of the programmed value. If the low voltage persists for more than 1/2 hour, the battery charger automatically terminates and indicates via the CHRG pin that the battery was unresponsive.Once the battery voltage is above 2.85V, the battery charger begins charging in full power constant-current mode. The current delivered to the battery will try to reach 1022V/RPROG. Depending on available input power and external load conditions, the battery charger may or may not be able to charge at the full programmed rate. The external load will always be prioritized over the battery charge current. The USB current limit programming will always be observed and only additional power will be available to charge the battery. When system loads are light, battery charge current will be maximized.Charge TerminationThe battery charger has a built-in safety timer. When the voltage on the battery reaches the pre-programmed ﬂ oat voltage of 4.200V, the battery charger will regulate the battery voltage and the charge current will decrease naturally. Once the battery charger detects that the battery has reached 4.200V, the four hour safety timer is started. After the safety timer expires, charging of the battery will discontinue and no more current will be delivered. Automatic RechargeAfter the battery charger terminates, it will remain off drawing only microamperes of current from the battery. If the portable product remains in this state long enough, the battery will eventually self discharge. To ensure that the battery is always topped off, a charge cycle will auto-matically begin when the battery voltage falls below 4.1V. In the event that the safety timer is running when the battery voltage falls below 4.1V, it will reset back to zero. To prevent brief excursions below 4.1V from resetting the safety timer, the battery voltage must be below 4.1V for more than 1.3ms. The charge cycle and safety timer will also restart if the VBUS UVLO cycles low and then high (e.g. VBUS, is removed and then replaced), or if the battery charger is cycled on and off by either the I2C port or the CHRGEN digital I/O pin.Charge CurrentThe charge current is programmed using a single resis-tor from PROG to ground. 1/1022th of the battery charge current is sent to PROG which will attempt to servo to 1.000V. Thus, the battery charge current will try to reach 1022 times the current in the PROG pin. The program resistor and the charge current are calculated using the following equations:1022V1022V

RPROG=,ICHG=

ICHGRPROG

In either the constant-current or constant-voltage charging modes, the voltage at the PROG pin will be proportional to the actual charge current delivered to the battery. There-fore, the actual charge current can be determined at any time by monitoring the PROG pin voltage and using the following equation:V

IBAT=PROG•1022

RPROG

In many cases, the actual battery charge current, IBAT, will be lower than ICHG due to limited input power available and prioritization with the system load drawn from VOUT.Charge Status IndicationThe CHRG pin indicates the status of the battery charger. Four possible states are represented by CHRG which in-clude charging, not charging, unresponsive battery, and battery temperature out of range.The signal at the CHRG pin can be easily recognized as one of the above four states by either a human or a 3567f15元器件交易网www.cecb2b.com

LTC3567OPERATION

microprocessor. An open-drain output, the CHRG pin can drive an indicator LED through a current limiting resistor for human interfacing or simply a pull-up resistor for mi-croprocessor interfacing.To make the CHRG pin easily recognized by both humans and microprocessors, the pin is either low for charging, high for not charging, or it is switched at high frequency (35kHz) to indicate the two possible faults, unresponsive battery and battery temperature out of range.When charging begins, CHRG is pulled low and remains low for the duration of a normal charge cycle. When charging is complete, i.e., the BAT pin reaches 4.200V and the charge current has dropped to one-tenth of the programmed value, the CHRG pin is released (Hi-Z). If a fault occurs, the pin is switched at 35kHz. While switching, its duty cycle is modulated between a high and low value at a very low frequency. The low and high duty cycles are disparate enough to make an LED appear to be on or off thus giving the appearance of “blinking”. Each of the two faults has its own unique “blink” rate for human recognition as well as two unique duty cycles for machine recognition. The CHRG pin does not respond to the C/10 threshold if the LTC3567 is in VBUS current limit. This prevents false end of charge indications due to insufﬁ cient power avail-able to the battery charger.Table 1 illustrates the four possible states of the CHRG pin when the battery charger is active. Table 1. CHRG SignalSTATUSChargingNot ChargingNTC FaultBad BatteryFREQUENCY0Hz0Hz35kHz35kHzMODULATION (BLINK) FREQUENCY0Hz (Lo-Z)0Hz (Hi-Z)1.5Hz AT 50%6.1Hz AT 50%DUTY CYCLES100%0%6.25%, 93.75%12.5%, 87.5%If a battery is found to be unresponsive to charging (i.e., its voltage remains below 2.85V for 1/2 hour), the CHRG pin gives the battery fault indication. For this fault, a human would easily recognize the frantic 6.1Hz “fast” blink of the LED while a microprocessor would be able to decode either the 12.5% or 87.5% duty cycles as a bad battery fault. Note that the LTC3567 is a 3-terminal PowerPath prod-uct where system load is always prioritized over battery charging. Due to excessive system load, there may not be sufﬁ cient power to charge the battery beyond the trickle charge threshold voltage within the bad battery timeout period. In this case, the battery charger will falsely indicate a bad battery. System software may then reduce the load and reset the battery charger to try again.Although very improbable, it is possible that a duty cycle reading could be taken at the bright-dim transition (low duty cycle to high duty cycle). When this happens the duty cycle reading will be precisely 50%. If the duty cycle reading is 50%, system software should disqualify it and take a new duty cycle reading.NTC ThermistorThe battery temperature is measured by placing a nega-tive temperature coefﬁ cient (NTC) thermistor close to the battery pack. To use this feature, connect the NTC thermistor, RNTC, be-tween the NTC pin and ground and a resistor, RNOM, from VBUS to the NTC pin. RNOM should be a 1% resistor with a value equal to the value of the chosen NTC thermistor at 25°C (R25). A 100k thermistor is recommended since thermistor current is not measured by the LTC3567 and will have to be budgeted for USB compliance.The LTC3567 will pause charging when the resistance of the NTC thermistor drops to 0.54 times the value of R25 or approximately 54k. For Vishay “Curve 1” thermistor, this corresponds to approximately 40°C. If the battery charger is in constant-voltage (ﬂ oat) mode, the safety timer also pauses until the thermistor indicates a return to a valid temperature. As the temperature drops, the resistance of the NTC thermistor rises. The LTC3567 is also designed to pause charging when the value of the NTC thermistor increases to 3.25 times the value of R25. For Vishay “Curve 1” this resistance, 325k, corresponds 3567fAn NTC fault is represented by a 35kHz pulse train whose duty cycle alternates between 6.25% and 93.75% at a 1.5Hz rate. A human will easily recognize the 1.5Hz rate as a “slow” blinking which indicates the out-of-range battery temperature while a microprocessor will be able to decode either the 6.25% or 93.75% duty cycles as an NTC fault.16元器件交易网www.cecb2b.com

LTC3567OPERATION

to approximately 0°C. The hot and cold comparators each have approximately 3°C of hysteresis to prevent oscillation about the trip point. Grounding the NTC pin disables the NTC charge pausing function.Thermal RegulationTo optimize charging time, an internal thermal feedback loop may automatically decrease the programmed charge current. This will occur if the die temperature rises to approximately 110°C. Thermal regulation protects the LTC3567 from excessive temperature due to high power operation or high ambient thermal conditions and allows the user to push the limits of the power handling capability with a given circuit board design without risk of damag-ing the LTC3567 or external components. The beneﬁ t of the LTC3567 thermal regulation loop is that charge current can be set according to actual conditions rather than worst-case conditions with the assurance that the battery charger will automatically reduce the current in worst-case conditions.I2C InterfaceThe LTC3567 may receive commands from a host (mas-ter) using the standard I2C 2-wire interface. The Timing Diagram shows the timing relationship of the signals on the bus. The two bus lines, SDA and SCL, must be high when the bus is not in use. External pull-up resistors or current sources, such as the LTC1694 I2C accelerator, are required on these lines. The LTC3567 is a receive-only (slave) device. The I2C control signals, SDA and SCL are scaled internally to the DVCC supply. DVCC should be con-nected to the same power supply as the microcontroller generating the I2C signals.The I2C port has an undervoltage lockout on the DVCC pin. When the DVCC is below approximately 1V, the I2C serial port is cleared and the buck-boost switching regulator is set to full scale.Bus SpeedThe I2C port is designed to be operated at speeds of up to 400kHz. It has built-in timing delays to ensure correct operation when addressed from an I2C compliant master device. It also contains input ﬁ lters designed to suppress glitches should the bus become corrupted.Start and Stop ConditionA bus master signals the beginning of a communication to a slave device by transmitting a Start condition. A Start condition is generated by transitioning SDA from high to low while SCL is high. When the master has ﬁ nished communicating with the slave, it issues a Stop condition by transitioning SDA from low to high while SCL is high. The bus is then free for communication with another I2C device.Byte FormatEach byte sent to the LTC3567 must be eight bits long followed by an extra clock cycle for the Acknowledge bit to be returned by the LTC3567. The data should be sent to the LTC3567 most signiﬁ cant bit (MSB) ﬁ rst.AcknowledgeThe Acknowledge signal is used for handshaking be-tween the master and the slave. An Acknowledge (active low) generated by the slave (LTC3567) lets the master know that the latest byte of information was received. The Acknowledge related clock pulse is generated by the master. The master releases the SDA line (high) during the Acknowledge clock cycle. The slave receiver must pull down the SDA line during the Acknowledge clock pulse so that it remains a stable low during the high period of this clock pulse.Slave AddressThe LTC3567 responds to only one 7-bit address which has been factory programmed to 0001001. The LSB of the address byte is 1 for Read and 0 for Write. This device is write only corresponding to an address byte of 00010010 (0x12). If the correct seven bit address is given but the R/W bit is 1, the LTC3567 will not respond.Bus Write OperationThe master initiates communication with the LTC3567 with a Start condition and a 7-bit address followed by the Write Bit R/W = 0. If the address matches that of the LTC3567, the LTC3567 returns an Acknowledge. The master should then deliver the most signiﬁ cant data byte. Again the LTC3567 acknowledges and the cycle is repeated for 3567f17元器件交易网www.cecb2b.com

LTC3567OPERATION

Table 2. I2C Serial Port Mapping (Defaults 0xFF00 in Reset State or if DVCC = 0V)A7A6A5A4A3A2A1A0B7Disable Battery ChargerB6Buck-Boost Regulator Mode (See Table 5)B5B4B3B2B1B0Reserved for Internal UseSwitching Regulator Voltage (See Table 4)Reserved for Internal Enable UseBuck-Boost RegulatorInput Current Limit (See Table 3)Table 3. USB Current Limit SettingsB10011B00101USB SETTING1x Mode (USB 100mA Limit)10x Mode (Wall 1A Limit)Suspend5x Mode (USB 500mA Limit)Table 4. Buck-Boost Regulator Servo VoltageA30000000011111111A20000111100001111A10011001100110011A00101010101010101SWITCHING REGULATORSERVO VOLTAGE0.425V0.450V0.475V0.500V0.525V0.550V0.575V0.600V0.625V0.650V0.675V0.700V0.725V0.750V0.775V0.800Vthe communication with a Stop condition. Alternatively, a Repeat-Start condition can be initiated by the master and another chip on the I2C bus can be addressed. This cycle can continue indeﬁ nitely and the LTC3567 will remember the last input of valid data that it received. Once all chips on the bus have been addressed and sent valid data, a global Stop condition can be sent and the LTC3567 will update its command latch with the data that it had received.In certain circumstances the data on the I2C bus may become corrupted. In these cases the LTC3567 responds appropriately by preserving only the last set of complete data that it has received. For example, assume the LTC3567 has been successfully addressed and is receiving data when a Stop condition mistakenly occurs. The LTC3567 will ignore this Stop condition and will not respond until a new Start condition, correct address, new set of data and Stop condition are transmitted.Likewise, with only one exception, if the LTC3567 was previously addressed and sent valid data but not updated with a Stop, it will respond to any Stop that appears on the bus, independent of the number of Repeat-Starts that have occurred. If a Repeat-Start is given and the LTC3567 successfully acknowledges its address and ﬁ rst byte, it will not respond to a Stop until both bytes of the new data have been received and acknowledged.Disabling the I2C PortThe I2C serial port can be disabled by grounding the DVCC pin. In this mode, control automatically passes to the individual logic input pins EN1 and CHRGEN. However, with the I2C port disabled, the programmable buck-boost switching regulator defaults to a ﬁ xed servo voltage of 0.8V in PWM mode, and the USB input current limit defaults to 1x mode (100mA limit). By default the battery charger will be enabled and the buck-boost will be disabled.Table 5. Buck-Boost Switching Regulator ModesB601SWITCHING REGULATOR MODEPWM ModeBurst Mode Operationthe total of one address byte and two data bytes. Each data byte is transferred to an internal holding latch upon the return of an Acknowledge. After both data bytes have been transferred to the LTC3567, the master may terminate 3567f18元器件交易网www.cecb2b.com

LTC3567OPERATION

Buck-Boost DC/DC Switching RegulatorThe LTC3567 contains a 2.25MHz constant-frequency volt-age mode buck-boost switching regulator. The regulator provides up to 1A of output load current. The buck-boost can be programmed to a minimum output voltage of 2.75V and can be used to power a microcontroller core, micro-controller I/O, memory, disk drive, or other logic circuitry. When controlled by I2C, the buck-boost has programmable set-points for on-the-ﬂ y power savings. To suit a variety of applications, a selectable mode function allows the user to trade off noise for efﬁ ciency. Two modes are available to control the operation of the LTC3567’s buck-boost regula-tor. At moderate to heavy loads, the constant frequency PWM mode provides the least noise switching solution. At lighter loads Burst Mode operation may be selected. The full-scale output voltage is programmed by a user-supplied resistive divider returned to the FB1 pin. An error ampliﬁ er compares the divided output voltage with a reference and adjusts the compensation voltage accordingly until the FB1 has stabilized to the selected reference voltage (0.425V to 0.8V). The buck-boost regulator also includes a soft-start to limit inrush current and voltage overshoot when powering on, short circuit current protection, and switch node slew limiting circuitry for reduced radiated EMI.Input Current LimitThe input current limit comparator will shut the input PMOS switch off once current exceeds 2.5A (typical). The 2.5A input current limit also protects against a grounded VOUT1 node.Output Overvoltage ProtectionIf the FB1 node were inadvertently shorted to ground, then the output would increase indeﬁ nitely with the maximum current that could be sourced from VIN1. The LTC3567 protects against this by shutting off the input PMOS if the output voltage exceeds a 5.6V (typical). Low Output Voltage OperationWhen the output voltage is below 2.65V (typical) during start-up, Burst Mode operation is disabled and switch D is turned off (allowing forward current through the well diode and limiting reverse current to 0mA).Buck-Boost Regulator PWM Operating ModeIn PWM mode the voltage seen at FB1 is compared to the selected reference voltage (0.425V to 0.8V). From the FB1 voltage an error ampliﬁ er generates an error signal seen at VC1. This error signal commands PWM waveforms that modulate switches A, B, C, and D. Switches A and B operate synchronously as do switches C and D. If VIN1 is signiﬁ cantly greater than the programmed VOUT1, then the converter will operate in buck mode. In this mode switches A and B will be modulated, with switch D always on (and switch C always off), to step down the input voltage to the cantly less than the programmed output. If VIN1 is signiﬁprogrammed VOUT1, then the converter will operate in boost mode. In this mode switches C and D are modulated, with switch A always on (and switch B always off), to step up the input voltage to the programmed output. If VIN1 is close to the programmed VOUT1, then the converter will operate in 4-switch mode. In this mode the switches sequence through the pattern of AD, AC, BD to either step the input voltage up or down to the programmed output.Buck-Boost Regulator Burst-Mode OperationIn Burst Mode operation, the buck-boost regulator uses a hysteretic FB1 voltage algorithm to control the output voltage. By limiting FET switching and using a hysteretic control loop, switching losses are greatly reduced. In this mode output current is limited to 50mA typical. While operating in Burst Mode operation, the output capacitor is charged to a voltage slightly higher than the regulation point. The buck-boost converter then goes into a sleep state, during which the output capacitor provides the load current. The output capacitor is charged by charg-ing the inductor until the input current reaches 275mA typical and then discharging the inductor until the reverse current reaches 0mA typical. This process is repeated until the feedback voltage has charged to 6mV above the regulation point. In the sleep state, most of the regulator’s circuitry is powered down, helping to conserve battery power. When the feedback voltage drops 6mV below the regulation point, the switching regulator circuitry is pow-ered on and another burst cycle begins. The duration for which the regulator sleeps depends on the load current and output capacitor value. The sleep time decreases as the load current increases. The maximum load current in 3567f19元器件交易网www.cecb2b.com

LTC3567OPERATION

Burst Mode operation is 50mA. The buck-boost regulator will not go to sleep if the current is greater than 50mA, and if the load current increases beyond this point while in Burst Mode operation the output will lose regulation. Burst Mode operation provides a signiﬁ cant improvement in efﬁ ciency at light loads at the expense of higher output ripple when compared to PWM mode. For many noise-sensitive systems, Burst Mode operation might be unde-sirable at certain times (i.e., during a transmit or receive cycle of a wireless device), but highly desirable at others (i.e. when the device is in low power standby mode). The B6 bit of the I2C port is used to enable or disable Burst Mode operation at any time, offering both low noise and low power operation when they are needed.Buck-Boost Regulator Soft-Start OperationSoft-start is accomplished by gradually increasing the reference voltage input to the error ampliﬁ er over a 0.5ms (typical) period. This limits transient inrush currents during start-up because the output voltage is always “in regula-tion.” Ramping the reference voltage input also limits the rate of increase in the VC1 voltage which helps minimize output overshoot during start-up. A soft-start cycle oc-curs whenever the buck-boost is enabled, or after a fault condition has occurred (thermal shutdown or UVLO). A soft-start cycle is not triggered by changing operating modes. This allows seamless operation when transitioning between Burst Mode operation and PWM mode.Low Supply OperationThe LTC3567 incorporates an undervoltage lockout cir-cuit on VOUT (connected to VIN1) which shuts down the buck-boost regulator when VOUT drops below 2.6V. This UVLO prevents unstable operation.APPLICATIONS INFORMATION

CLPROG Resistor and CapacitorAs described in the High Efﬁ ciency Switching PowerPath Controller section, the resistor on the CLPROG pin deter-mines the average input current limit when the switching regulator is set to either the 1x mode (USB 100mA), the 5x mode (USB 500mA) or the 10x mode. The input cur-rent will be comprised of two components, the current that is used to drive VOUT and the quiescent current of the switching regulator. To ensure that the USB speciﬁ cation is strictly met, both components of input current should be considered. The Electrical Characteristics table gives values for quiescent currents in either setting as well as current limit programming accuracy. To get as close to the 500mA or 100mA speciﬁ cations as possible, a 1% resistor should be used. Recall that IVBUS = IVBUSQ + VCLPROG/RCLPROG • (hCLPROG + 1).An averaging capacitor or an R-C combination is required in parallel with the CLPROG resistor so that the switching regulator can determine the average input current. This network also provides the dominant pole for the feedback loop when current limit is reached. To ensure stability, the capacitor on CLPROG should be 0.1μF or larger. Choosing the PowerPath InductorBecause the input voltage range and output voltage range of the PowerPath switching regulator are both fairly nar-row, the LTC3567 was designed for a speciﬁ c inductance value of 3.3μH. Some inductors which may be suitable for this application are listed in Table 6.Table 6. Recommended Inductors for PowerPath ControllerMAXINDUCTOR L IDC TYPE(μH)(A)LPS4018D53LCDB318CWE-TPCType M1CDRH6D12CDRH6D383.33.33.33.33.33.32.22.261.551.952.23.5MAX DCR (Ω)0.080.0340.0700.065SIZE IN mm (L × W × H)MANUFACTURER3.9 × 3.9 × 1.7Coilcraftwww.coilcraft.com5.0 × 5.0 × 3.0Toko3.8 × 3.8 × 1.8www.toko.com4.8 × 4.8 × 1.8Würth Elektronikwww.we-online.com0.06256.7 × 6.7 × 1.5Sumida0.0207.0 × 7.0 × 4.0www.sumida.com3567f20元器件交易网www.cecb2b.com

LTC3567APPLICATIONS INFORMATION

VBUS and VOUT Bypass CapacitorsThe style and value of capacitors used with the LTC3567 determine several important parameters such as regulator control-loop stability and input voltage ripple. Because the LTC3567 uses a step-down switching power supply from VBUS to VOUT, its input current waveform contains high frequency components. It is strongly recommended that a low equivalent series resistance (ESR) multilayer ceramic capacitor be used to bypass VBUS. Tantalum and aluminum capacitors are not recommended because of their high ESR. The value of the capacitor on VBUS directly controls the amount of input ripple for a given load cur-rent. Increasing the size of this capacitor will reduce the input ripple.To prevent large VOUT voltage steps during transient load conditions, it is also recommended that a ceramic capaci-tor be used to bypass VOUT. The output capacitor is used in the compensation of the switching regulator. At least 4μF of actual capacitance with low ESR are required on VOUT. Additional capacitance will improve load transient performance and stability. Multilayer ceramic chip capacitors typically have excep-tional ESR performance. MLCCs combined with a tight board layout and an unbroken ground plane will yield very good performance and low EMI emissions.There are several types of ceramic capacitors available, each having considerably different characteristics. For example, X7R ceramic capacitors have the best voltage and temperature stability. X5R ceramic capacitors have appar-ently higher packing density but poorer performance over their rated voltage and temperature ranges. Y5V ceramic capacitors have the highest packing density, but must be used with caution, because of their extreme nonlinear characteristic of capacitance vs voltage. The actual in-circuit capacitance of a ceramic capacitor should be measured with a small AC signal (ideally less than 200mV) as is expected in-circuit. Many vendors specify the capacitance vs voltage with a 1VRMS AC test signal and as a result overstate the capacitance that the capacitor will present in the application. Using similar operating conditions as the application, the user must measure or request from the vendor the actual capacitance to determine if the selected capacitor meets the minimum capacitance that the application requires.Buck-Boost Regulator Inductor SelectionMany different sizes and shapes of inductors are avail-able from numerous manufacturers. Choosing the right inductor from such a large selection of devices can be overwhelming, but following a few basic guidelines will make the selection process much simpler.The buck-boost converter is designed to work with induc-tors in the range of 1μH to 5μH. For most applications a 2.2μH inductor will sufﬁ ce. Larger value inductors reduce ripple current which improves output ripple voltage. Lower value inductors result in higher ripple current and improved transient response time. To maximize efﬁ ciency, choose an inductor with a low DC resistance. For a 3.3V output, efﬁ ciency is reduced about 3% for a 100mΩ series resis-tance at 1A load current, and about 2% for 300mΩ series resistance at 200mA load current. Choose an inductor with a DC current rating at least two times larger than the maximum load current to ensure that the inductor does not saturate during normal operation. If output short circuit is a possible condition, the inductor should be rated to handle the 2.5A maximum peak current speciﬁ ed for the buck-boost converter.Different core materials and shapes will change the size/current and price/current relationship of an induc-tor. Toroid or shielded pot cores in ferrite or Permalloy materials are small and do not radiate much energy, but generally cost more than powdered iron core inductors with similar electrical characteristics. Inductors that are very thin or have a very small volume typically have much higher core and DCR losses, and will not give the best ef-ﬁ ciency. The choice of which style inductor to use often depends more on the price vs size, performance and any radiated EMI requirements than on what the LTC3567 requires to operate.The inductor value also has an effect on Burst Mode op-eration. Lower inductor values will cause the Burst Mode operation switching frequencies to increase.Table 7 shows several inductors that work well with the LTC3567’s buck-boost regulator. These inductors offer a good compromise in current rating, DCR and physical size. Consult each manufacturer for detailed information on their entire selection of inductors.3567f21元器件交易网www.cecb2b.com

LTC3567APPLICATIONS INFORMATION

Table 7. Recommended Inductors for Buck-Boost RegulatorMAX MAX INDUCTOR L IDC DCR TYPE(μH)(A)(Ω)LPS4018D53LC7440430022CDRH4D22/HPSD143.32.22.02.22.22.02.22.53.252.52.40.080.070.02SIZE IN mm (L × W × H)MANUFACTURER3.9 × 3.9 × 1.7Coilcraft3.9 × 3.9 × 1.7www.coilcraft.com5.0 × 5.0 × 3.0Tokowww.toko.com0.0284.8 × 4.8 × 2.8Würth-Elektronikwww.we-online.com0.0444.7 × 4.7 × 2.4Sumidawww.sumida.com2.560.0455.2 × 5.2 × 1.45Cooperwww.cooper.comIn some cases the battery charger may be programmed (with the PROG pin) to deliver the maximum safe charging current without regard to the USB speciﬁ cations. If there is insufﬁ cient current available to charge the battery at the programmed rate, the PowerPath regulator will reduce ed charge current until the system load on VOUT is satisﬁ ed. Programming the and the VBUS current limit is satisﬁbattery charger for more current than is available will not cause the average input current limit to be violated. It will merely allow the battery charger to make use of all available power to charge the battery as quickly as possible, and with minimal power dissipation within the battery charger.Alternate NTC Thermistors and BiasingThe LTC3567 provides temperature qualiﬁ ed charging if a grounded thermistor and a bias resistor are connected to NTC. By using a bias resistor whose value is equal to the room temperature resistance of the thermistor (R25) the upper and lower temperatures are pre-programmed to approximately 40°C and 0°C, respectively (assuming a Vishay “Curve 1” thermistor).The upper and lower temperature thresholds can be ad-justed by either a modiﬁ cation of the bias resistor value or by adding a second adjustment resistor to the circuit. If only the bias resistor is adjusted, then either the upper or the lower threshold can be modiﬁ ed but not both. The other trip point will be determined by the characteristics of the thermistor. Using the bias resistor in addition to an adjustment resistor, both the upper and the lower tem-perature trip points can be independently programmed with the constraint that the difference between the upper and lower temperature thresholds cannot decrease. Ex-amples of each technique follow.NTC thermistors have temperature characteristics which are indicated on resistance-temperature conversion tables. The Vishay-Dale thermistor NTHS0603N011-N1003F, used in the following examples, has a nominal value of 100k and follows the Vishay “Curve 1” resistance-temperature characteristic.In the explanation below, the following notation is used. R25 = Value of the thermistor at 25°C RNTC|COLD = Value of thermistor at the cold trip point3567fBuck-Boost Regulator Input/Output Capacitor SelectionLow ESR MLCC capacitors should also be used at both the buck-boost regulator output (VOUT1) and the buck-boost regulator input supply (VIN1). Only X5R or X7R ceramic capacitors should be used because they retain their capacitance over wider voltage and temperature ranges than other ceramic types. A 22μF output capaci-tor is sufﬁ cient for most applications. The buck-boost regulator input supply should be bypassed with a 2.2μF capacitor. Consult with capacitor manufacturers for de-tailed information on their selection and speciﬁ cations of ceramic capacitors. Many manufacturers now offer very thin (<1mm tall) ceramic capacitors ideal for use in height restricted designs. Table 8 shows a list of several ceramic capacitor manufacturers.Table 8. Recommended Ceramic Capacitor ManufacturersMANUFACTURERAVXMurataTaiyo YudenVishay SiliconixTDKWEBSITEwww.avxcorp.comwww.murata.comwww.t-yuden.comwww.vishay.comwww.tdk.comOver-Programming the Battery ChargerThe USB high power speciﬁ cation allows for up to 2.5W to be drawn from the USB port (5V × 500mA). The PowerPath switching regulator transforms the voltage at VBUS to just above the voltage at BAT with high efﬁ ciency, while limiting power to less than the amount programmed at CLPROG. 22元器件交易网www.cecb2b.com

LTC3567APPLICATIONS INFORMATION

RNTC|HOT = Value of thermistor at the hot trip point rCOLD = Ratio of RNTC|COLD to R25 rHOT= Ratio of RNTC|HOT to R25 RNOM = Primary thermistor bias resistor (see Figure 4a) R1 = Optional temperature range adjustment resistor (see Figure 4b)The trip points for the LTC3567’s temperature qualiﬁ ca-tion are internally programmed at 0.349 • VBUS for the hot threshold and 0.765 • VBUS for the cold threshold.Therefore, the hot trip point is set when:RNTC|HOT

•VBUS=0.349•VBUS

RNOM+RNTC|HOT

and the cold trip point is set when:RNTC|COLD

•VBUS=0.765•VBUS

R+RNTC|COLD NOM

Solving these equations for RNTC|COLD and RNTC|HOT results in the following: RNTC|HOT = 0.536•RNOMand RNTC|COLD = 3.25•RNOMBy setting RNOM equal to R25, the above equations result in rHOT = 0.536 and rCOLD = 3.25. Referencing these ratios to the Vishay Resistance-Temperature Curve 1 chart gives a hot trip point of about 40°C and a cold trip point of about 0°C. The difference between the hot and cold trip points is approximately 40°C.By using a bias resistor, RNOM, different in value from R25, the hot and cold trip points can be moved in either direction. The temperature span will change somewhat due to the nonlinear behavior of the thermistor. The following equations can be used to easily calculate a new value for the bias resistor:rHOT•R250.536r

RNOM=COLD•R25

3.25 RNOM=

where rHOT and rCOLD are the resistance ratios at the de-sired hot and cold trip points. Note that these equations are linked. Therefore, only one of the two trip points can be chosen, the other is determined by the default ratios designed in the IC. Consider an example where a 60°C hot trip point is desired.From the Vishay Curve 1 R-T characteristics, rHOT is 0.2488 at 60°C. Using the above equation, RNOM should be set to 46.4k. With this value of RNOM, the cold trip point is about 16°C. Notice that the span is now 44°C rather than the previous 40°C. This is due to the decrease in “tem-perature gain” of the thermistor as absolute temperature increases.The upper and lower temperature trip points can be in-dependently programmed by using an additional bias resistor as shown in Figure 4b. The following formulas can be used to compute the values of RNOM and R1:rCOLD−rHOT•R25

2.714

R1=0.536•RNOM−rHOT•R25RNOM=

For example, to set the trip points to 0°C and 45°C with a Vishay Curve 1 thermistor chooseRNOM=

3.266−0.4368

•100k=104.2k

2.714

The nearest 1% value is 105k R1 = 0.536•105k – 0.4368•100k = 12.6kThe nearest 1% value is 12.7k. The ﬁ nal solution is shown in Figure 4b and results in an upper trip point of 45°C and a lower trip point of 0°C.USB Inrush LimitingWhen a USB cable is plugged into a portable product, the inductance of the cable and the high-Q ceramic input capacitor form an L-C resonant circuit. If the cable does not have adequate mutual coupling or if there is not much impedance in the cable, it is possible for the voltage at the input of the product to reach as high as twice the USB voltage (~10V) before it settles out. To prevent excessive voltage from damaging the LTC3567 during a hot insertion, 3567f23元器件交易网www.cecb2b.com

LTC3567APPLICATIONS INFORMATION

VBUSVBUS0.765 • VBUSLTC3567NTC BLOCKVBUSVBUSLTC3567NTC BLOCKRNOM100kNTC3RNTC100k0.349 • VBUS–TOO_COLDRNOM105kNTC3R112.7k0.765 • VBUS–TOO_COLD+–TOO_HOT+–0.349 • VBUSTOO_HOT++NTC_ENABLERNTC100k++NTC_ENABLE0.017 • VBUS–3567 F04a0.017V • VBUS–3567 F04b(a)

Figure 4. NTC Circuits(b)

it is best to have a low voltage coefﬁ cient capacitor at the VBUS pin to the LTC3567. This is achievable by selecting an MLCC capacitor that has a higher voltage rating than that required for the application. For example, a 16V, X5R, 10μF capacitor in a 1206 case would be a more conservative choice than a 6.3V, X5R, 10μF capacitor in a smaller 0805 case. The size of the input overshoot will be determined by the “Q” of the resonant tank circuit formed by CIN and the input lead inductance. It is recommended to measure the input ringing with the selected components to verify compliance with the Absolute Maximum speciﬁ cations.Alternatively, the following soft connect circuit (Figure 5) can be employed. In this circuit, capacitor C1 holds MP1 off when the cable is ﬁ rst connected. Eventually C1 begins to charge up to the USB input voltage applying increasing gate support to MP1. The long time constant of R1 and C1 prevent the current from building up in the cable too fast thus dampening out any resonant overshoot.MP1Si23335V USBINPUTUSB CABLEC1100nFR140kVBUSC210μFscale output voltage is programmed using a resistor divider from the VOUT1 pin connected to the FB1 pin such that:󰀁R1󰀄

VOUT1=VFB1󰀂+1󰀅

R󰀃󰀆 FB

where VFB1 ranges from 0.425V to 0.8V (see Figure 6).Closing the Feedback LoopThe LTC3567 incorporates voltage mode PWM control. The control to output gain varies with operation region (buck, boost, buck-boost), but is usually no greater than 20. The output ﬁ lter exhibits a double pole response given by:1fFILTER_POLE=Hz2•π•L•C OUTWhere COUT is the output ﬁ lter capacitor.The output ﬁ lter zero is given by:1

fFILTER_ZERO=Hz

2•π•R•CESROUT

where RESR is the capacitor equivalent series resistance.A troublesome feature in boost mode is the right-half plane zero (RHP), and is given by:VIN12

fRHPZ=Hz

2•π•I•L•V OUTOUT1

The loop gain is typically rolled off before the RHP zero frequency.3567fLTC3567GND3567 F05Figure 5. USB Soft Connect CircuitBuck-Boost Regulator Output Voltage ProgrammingThe buck-boost regulator can be programmed for output voltages greater than 2.75V and less than 5.5V. The full-24元器件交易网www.cecb2b.com

LTC3567APPLICATIONS INFORMATION

A simple Type I compensation network (as shown in Figure 6) can be incorporated to stabilize the loop but at –

the cost of reduced bandwidth and slower transient re-+

sponse. To ensure proper phase margin, the loop must cross unity-gain a decade before the LC double pole.VOUT10.8VERRORAMPFB1CP1R1attempting to cross over after the LC double pole, the system must still cross over before the boost right-half plane zero. If unity gain is not reached sufﬁ ciently before the right-half plane zero, then the –180° of phase lag from the LC double pole combined with the –90° of phase lag from the right-half plane zero will result in negating the phase bump of the compensator.The compensator zeros should be placed either before or only slightly after the LC double pole such that their positive phase contributions offset the –180° that occurs at the ﬁ lter double pole. If they are placed at too low of a frequency, they will introduce too much gain to the system and the crossover frequency will be too high. The two high frequency poles should be placed such that the system crosses unity gain during the phase bump introduced by the zeros and before the boost right-half plane zero and such that the compensator bandwidth is less than the bandwidth of the error amp (typically 900kHz). If the gain of the compensation network is ever greater than the gain of the error ampliﬁ er, then the error ampliﬁ er no longer acts as an ideal op-amp, and another pole will be introduced at the same point.Recommended Type III compensation components for a 3.3V output: R1: 324kΩ RFB: 105kΩ C1: 10pF R2: 15kΩ C2: 330pF R3: 121kΩ C3: 33pF COUT: 22μF LOUT: 2.2μH Printed Circuit Board Layout ConsiderationsIn order to be able to deliver maximum current under all conditions, it is critical that the Exposed Pad on the backside of the LTC3567 package be soldered to the PC board ground. Failure to make thermal contact between 3567fVC1RFB

3567 F06

Figure 6. Error Ampliﬁ er with Type I CompensationThe unity-gain frequency of the error ampliﬁ er with the Type I compensation is given by:1

fUG=Hz

2•π•R1•CP1

Most applications demand an improved transient response –to allow a smaller output ﬁ lter capacitor. To achieve a higher +

bandwidth, Type III compensation is required. Two zeros are required to compensate for the double-pole response. Type III compensation also reduces any VOUT1 overshoot seen at start-up.The compensation network depicted in Figure 7 yields the transfer function:VC11(1+sR2C2)•(1+s(R1+R3)C3)

=•

VOUT1R1•(C1+C2)s•󰀁1+sR2C1C2󰀄•(1+sR3C3)

󰀂󰀃󰀆C1+C2󰀅

VOUT10.8VERRORAMPFB1C2R1R3C3VC1R2C1RFB3567 F07Figure 7. Error Ampliﬁ er with Type III CompensationA Type III compensation network attempts to introduce a phase bump at a higher frequency than the LC double pole. This allows the system to cross unity gain after the LC double pole, and achieve a higher bandwidth. While 25元器件交易网www.cecb2b.com

LTC3567APPLICATIONS INFORMATION

the Exposed Pad on the backside of the package and the copper board will result in higher thermal resistances.Furthermore, due to its high frequency switching cir-cuitry, it is imperative that the input capacitors, induc-tors, and output capacitors be as close to the LTC3567 as possible and that there be an unbroken ground plane under the LTC3567 and all of its external high frequency components. High frequency currents, such as the VBUS, nd VIN1, and VOUT1 currents on the LTC3567, tend to ﬁtheir way along the ground plane in a myriad of paths ranging from directly back to a mirror path beneath the incident path on the top of the board. If there are slits or cuts in the ground plane due to other traces on that layer, the current will be forced to go around the slits. If high frequency currents are not allowed to ﬂ ow back through their natural least-area path, excessive voltage will build up and radiated emissions will occur. There should be a group of vias under the grounded backside of the pack-age leading directly down to an internal ground plane. To minimize parasitic inductance, the ground plane should be on the second layer of the PC board.When laying out the printed circuit board, the following checklist should be used to ensure proper operation of the LTC3567.1. Are the capacitors at VBUS, VIN1, and VOUT1 as close as possible to the LTC3567? These capacitors provide the AC current to the internal power MOSFETs and their drivers. Minimizing inductance from these capacitors to the LTC3567 is a top priority.2. Are COUT and L1 closely connected? The (-) plate of COUT returns current to the GND plane, and then back to CIN.3. Keep sensitive components away from the SW pins.Battery Charger Stability ConsiderationsThe LTC3567’s battery charger contains both a constant-voltage and a constant-current control loop. The constant-voltage loop is stable without any compensation when a battery is connected with low impedance leads. Excessive lead length, however, may add enough series inductance to require a bypass capacitor of at least 1μF from BAT to GND. Furthermore, when the battery is disconnected, a 4.7μF capacitor in series with a 0.2Ω to 1Ω resistor from BAT to GND is required to keep ripple voltage low.High value, low ESR multilayer ceramic chip capacitors reduce the constant-voltage loop phase margin, possibly resulting in instability. Ceramic capacitors up to 22μF may be used in parallel with a battery, but larger ceramics should be decoupled with 0.2Ω to 1Ω of series resistance.3567 F08Figure 8. Higher Frequency Ground Currents Follow Their Incident Path. Slices in the Ground Plane Cause High Voltage and Increased Emissions.The GATE pin for the external ideal diode controller has extremely limited drive current. Care must be taken to minimize leakage to adjacent PC board traces. 100nA of leakage from this pin will introduce an offset to the 15mV ideal diode of approximately 10mV. To minimize leakage, the trace can be guarded on the PC board by surrounding it with VOUT connected metal, which should generally be less than one volt higher than GATE.In constant-current mode, the PROG pin is in the feed-back loop rather than the battery voltage. Because of the additional pole created by any PROG pin capacitance, capacitance on this pin must be kept to a minimum. With no additional capacitance on the PROG pin, the battery charger is stable with program resistor values as high as 25k. However, additional capacitance on this node re-duces the maximum allowed program resistor. The pole frequency at the PROG pin should be kept above 100kHz. Therefore, if the PROG pin has a parasitic capacitance, CPROG, the following equation should be used to calculate the maximum resistance value for RPROG:1

RPROG≤

2π•100kHz•CPROG

3567f26元器件交易网www.cecb2b.com

LTC3567TYPICAL APPLICATIONS

Direct Pin Controlled LTC3567 USB Power Manager with 3.3V/1A Buck-BoostL13.3μHVBUSC110μF100kNTC100kTPROGGNDCLPROG2k0.1μF3.01kCHRGVIN1SWAB1PUSH BUTTONMICROCONTROLLER1μFDVCCCHRGENLDO3V3SWCD1VOUT1FB1VC1EN12GNDI2C10pF121k324kPARTS LISTC1: MURATA GRM21BR61A/06KE19C2,C3: TAIYO-YUDEN JMK212BJ226MGL1: COILCRAFT LPS4018-332MLCL2: COILCRAFT LPS4018-222MLC330pF15k105k3567 TA02USB4.5V TO 5.5VSWVOUTLTC3567GATEBATOPTIONAL1kC222μFTOOTHERLOADS+Li-Ion2.2μFL22.2μH33pFC322μF3.3V/1ADISK DRIVEPACKAGE DESCRIPTION

UF Package24-Lead Plastic QFN (4mm × 4mm)(Reference LTC DWG # 05-08-1697 Rev B)BOTTOM VIEW—EXPOSED PAD

4.00± 0.10(4 SIDES)0.70±0.05PIN 1TOP MARK(NOTE 6)0.75± 0.05R = 0.115TYPPIN 1 NOTCHR = 0.20 TYP OR 0.35× 45° CHAMFER

23240.40± 0.10124.50± 0.052.45± 0.053.10± 0.05(4 SIDES)2.45± 0.10(4-SIDES)PACKAGEOUTLINE0.25±0.050.50 BSCRECOMMENDED SOLDER PAD PITCH AND DIMENSIONS

0.200 REF0.00 – 0.05(UF24) QFN 01050.25± 0.050.50 BSCNOTE:

1. DRAWING PROPOSED TO BE MADE A JEDEC PACKAGE OUTLINE MO-220 VARIATION (WGGD-X)—TO BE APPROVED2. DRAWING NOT TO SCALE

3. ALL DIMENSIONS ARE IN MILLIMETERS

4. DIMENSIONS OF EXPOSED PAD ON BOTTOM OF PACKAGE DO NOT INCLUDE

MOLD FLASH. MOLD FLASH, IF PRESENT, SHALL NOT EXCEED 0.15mm ON ANY SIDE, IF PRESENT5. EXPOSED PAD SHALL BE SOLDER PLATED

6. SHADED AREA IS ONLY A REFERENCE FOR PIN 1 LOCATION ON THE TOP AND BOTTOM OF PACKAGE

3567fInformation furnished by Linear Technology Corporation is believed to be accurate and reliable. However, no responsibility is assumed for its use. Linear Technology Corporation makes no representa-tion that the interconnection of its circuits as described herein will not infringe on existing patent rights.27元器件交易网www.cecb2b.com

LTC3567RELATED PARTS

PART NUMBERDESCRIPTIONLTC3440LTC3441/LTC3442LTC3442LTC3455LTC3538LTC3550600mA (IOUT), 2MHz Synchronous Buck-Boost DC/DC Converter1.2A (IOUT), Synchronous Buck-Boost DC/DC Converters, LTC3441 (1MHz), LTC3443 (600kHz)COMMENTSVIN: 2.5V to 5.5V, VOUT: 2.5V to 5.5VIQ = 25μA, ISD < 1μA, MS, DFN PackageVIN: 2.5V to 5.5V, VOUT: 2.4V to 5.25VIQ = 25μA, ISD < 1μA, MS, DFN Package1.2A (IOUT), 2MHz Synchronous Buck-Boost DC/DC VIN: 2.4V to 5.5V, VOUT: 2.4V to 5.25VConverterIQ = 28μA, ISD < 1μA, MS PackageDual DC/DC Converter with USB Power Management and Li-Ion Battery Charger800mA, 2MHz Synchronous Buck-Boost DC/DC ConverterDual Input USB/AC Adapter Li-Ion Battery Charger with adjustable output 600mA Buck ConverterDual Input USB/AC Adapter Li-Ion Battery Charger with 600mA Buck ConverterEfﬁ ciency >96%, Accurate USB Current Limiting (500mA/100mA), 4mm × 4mm QFN-24 PackageVIN: 2.4V to 5.5V, VOUT: 1.8V to 5.25VIQ = 35μA, 2mm × 3mm DFN-8 PackageSynchronous Buck Converter, Efﬁ ciency: 93%, Adjustable Output at 600mA; Charge Current: 950mA Programmable, USB Compatible, Automatic Input Power Detection and Selection, 3mm × 5mm DFN-16 PackageSynchronous Buck Converter, Efﬁ ciency: 93%, Output: 1.875V at 600mA; Charge Current: 950mA Programmable, USB Compatible, Automatic Input Power Detection and Selection, 3mm × 5mm DFN-16 PackageLTC3550-1LTC3555Switching USB Power Manager with Li-Ion/Polymer Complete Multi-Function PMIC: Switchmode Power Manager and Three Buck Charger, Triple Synchronous Buck Converter Plus Regulators Plus LDO; Charge Current Programmable Up to 1.5A from Wall LDOAdapter Input, Thermal Regulation Synchronous Buck Converters Efﬁ ciency: >95%, ADJ Outputs: 0.8V to 3.6V at 400mA/400mA/1A Bat-Track Adaptive Output Control, 200mΩ Ideal Diode, 4mm × 5mm QFN-28 PackageSwitching USB Power Manager with Li-Ion/Polymer Complete Multi-Function PMIC: Switching Power Manager, 1A Buck-Boost Plus Charger, 1A Buck-Boost Plus Dual Sync Buck 2 Buck Regulators Plus LDO, ADJ Out Down to 0.8V at 400mA/400mA/1A, Converter Plus LDOSynchronous Buck/Buck-Boost Converter Efﬁ ciency: >95%; Charge Current Programmable up to 1.5A from Wall Adapter Input, Thermal Regulation, Bat-Track Adaptive Output Control, 180mΩ Ideal Diode, 4mm × 5mm QFN-28 PackageUSB Power Manager with Li-Ion/Polymer Charger, Triple Synchronous Buck Converter Plus LDOComplete Multi-Function PMIC: Linear Power Manager and Three Buck Regulators Charge Current Programmable Up to 1.5A from Wall Adapter Input, Thermal Regulation Synchronous Buck Converters Efﬁ ciency: >95%, ADJ Output: 0.8V to 3.6V at 400mA/400mA/600mA Bat-Track Adaptive Output Control, 200mΩ Ideal Diode, 4mm × 4mm QFN-28 PackageAdjustable Synchronous Buck Converters, Efﬁ ciency: >90%, Outputs: Down to 0.8V at 400mA for Each, Charge Current Programmable Up to 950mA, USB Compatible, 3mm × 3mm QFN-16 PackageLTC3556LTC3557/LTC3557-1LTC3559Linear USB Li-Ion/Polymer Battery Chargerwith Dual Synchronous Buck ConverterLTC3566Switching USB Power Manager with Li-Ion/Polymer Multi-Function PMIC: Switchmode Power Manager and 1A Buck-Boost Regulator Charger, 1A Buck-Boost Converter Plus LDOPlus LDO, Charge Current Programmable up to 1.5A from Wall Adapter Input, Thermal Regulation Synchronous Buck-Boost Converters Efﬁ ciency: >95%, ADJ Output: Down to 0.8V at 1A, Bat-Track Adaptive Output Control, 180mΩ Ideal Diode, 4mm × 4mm QFN-24 PackageUSB Power Controller and Battery ChargerLinear USB Power Manager with OVP,Ideal Diode Controller and Li-Ion ChargerLinear USB Power Manager with Ideal Diode Controller and Li-Ion ChargerHigh Efﬁ ciency USB Power Manager andBattery ChargerHigh Efﬁ ciency USB Power Manager andBattery Charger with Regulated Output VoltageCharges Single-Cell Li-Ion Batteries Directly From USB Port,Thermal Regulation, 4mm × 4mm QFN-16 Package13V Overvoltage Transient Protection, Thermal Regulation 200mΩ Ideal Diode with <50mΩ Option, 3mm × 4mm QFN-14 PackageCharges Single Cell Li-Ion Batteries Directly from a USB Port, Thermal Regulation, 200mΩ Ideal Diode with <50mΩ Option,3mm × 4mm QFN-14 PackageMaximizes Available Power from USB Port, Bat-Track, “Instant-On” Operation, 1.5A Maximum Charge Current, 180mΩ Ideal Diode with <50mΩ Option, 3.3V/25mA Always-On LDO, 3mm × 4mm DFN-14 PackageMaximizes Available Power from USB Port, Bat-Track, “Instant-On” Operation, 1.5A Maximum Charge Current, 180mΩ Ideal Diode with <50mΩ Option, Automatic Charge Current Reduction Maintains 3.6V Minimum VOUT, Battery Charger Disabled when all Logic Inputs are Grounded, 3mm × 4mm DFN-14 Package3567fLT 0608 • PRINTED IN USA

LTC4055LTC4067LTC4085LTC4088LTC4088-1/LTC4088/228Linear Technology Corporation1630 McCarthy Blvd., Milpitas, CA 95035-7417 (408) 432-1900 ● FAX: (408) 434-0507 ● www.linear.com© LINEAR TECHNOLOGY CORPORATION 2008

因篇幅问题不能全部显示，请点此查看更多更全内容

查看全文